Coo-var Suregrip

£56.73

Coo-var Suregrip is a ready mixed, single pack air drying aggregated floor paint

Suregrip provides a rough high build anti slip finish and is suitable for concrete, metal, wood and GRP surfaces and is an ideal floor coating to prevent slips and falls on stairways, walkways, ramps and around machinery. This coating provides a rough anti-slip finish when dry and also provides durability, decoration and protection.

If this product is used on most floors and other areas where moisture and other substances occur, then this may cause the area to become slippery. Recommended use for this coating is on suitably prepared concrete, wood, metal and GRP for foot traffic, light truck and occasional heavy truck traffic.

Suregrip should only be applied by a brush or short/medium roller with a wet film thickness of 100-150 microns or dry film thickness of 60-100 microns.

When applying the product all surfaces should be clean, dry and free from any contaminants.

For concrete – Power floated, granolithic and smooth surfaces should be roughened first to provide a good “key” for the paint. This can be done mechanically by abrading. These processes will have the advantage in addition to preparing the surface of also removing dirt and laitance. New concrete must be allowed to cure thoroughly which can take up to 3 months.

Apply a 10% thinner coat of Coo-Var High Performance Primer to prime and seal the surface prior to applying Coo-Var Suregrip.

For Existing painted surfaces – Surfaces should be cleaned, degreased and sanded to ensure an adequate “key” is produced. Remove all loose and flaking material and treat bare areas as a new substrate and prepare accordingly.

It is available in a range of 9 different colours in 5 litre containers.

SKU: N/A Categories: ,

Description

Coo-Var Suregrip anti-slip floor paint is a ready-mixed floor coating for suitable primed concrete, wood, metal and GRP which provides a rough, anti-slip finish when dry. Suregrip provides durability, decoration and protection. Suitable for indoor and outdoor use.

Coo-Var Suregrip is a safety coating suitable for indoor and outdoor use where a sure foothold is required. Ideal for boats, steps and stairways, disabled ramps, doorways, machinery areas, most floors and other areas where moisture and other substances may cause the floor to be slippery. Suitable for use on suitably prepared concrete, wood, metal and GRP. For foot, light truck and occasional heavy truck use.

When applying the product all surfaces should be clean, dry and free from any contaminants.

For concrete – Power floated, granolithic and smooth surfaces should be roughened first to provide a good “key” for the paint. This can be done mechanically by abrading. These processes will have the advantage in addition to preparing the surface of also removing dirt and laitance. New concrete must be allowed to cure thoroughly which can take up to 3 months.

Apply a 10% thinner coat of Coo-Var High Performance Primer to prime and seal the surface prior to applying Coo-Var Suregrip.

For Existing painted surfaces – Surfaces should be cleaned, degreased and sanded to ensure an adequate “key” is produced. Remove all loose and flaking material and treat bare areas as a new substrate and prepare accordingly.

This coating should only be applied with either a brush or short/medium roller with a wet film thickness of 100-150 microns or a dry film thickness of 60-100 microns.

The drying time for Suregrip is 6 hours at 20°C for it to be touch dry, it being hard dry is 24 hours at 20°C and for it to be fully hardened will take 5-7 days at 20°C.

This product comes in a range of 9 different colours including blue, red, green, dark green, black, grey, white, light grey and yellow. It is available in 5 litre containers.

Surface Preparation

Concrete:

Power floated, granolithic and smooth surfaces should be roughened first to provide a good “key” for the paint. This can be done mechanically by abrading. These processes will have the advantage in addition to preparing the surface of also removing dirt and laitance. New concrete must be allowed to cure thoroughly which can take up to 3 months.

Apply a 10% thinner coat of Coo-Var High Performance Primer to prime and seal the surface prior to applying Coo-Var Suregrip.

Existing Painted Surfaces: 

Surfaces should be cleaned, degreased and sanded to ensure an adequate “key” is produced. Remove all loose and flaking material and treat bare areas as a new substrate and prepare accordingly.

Technical Data

Download Datasheet Download Datasheet

Volume Solids (ISO 3223):  60%
VOC Content:  343 g/lt
Flash point (ISO 3679):  32c
Dry Film thickness:  60-100 microns
Wet Film thickness:  60-100 microns
Theoretical coverage:  6-10 sq.m/lt
Touch Dry 20c:  6 hrs
Hard Dry 20c:  24 hrs
Thinner:  Coo-var Thinner No. 14
H&S:  Observe the precautionary information on the container. Refer to MSDS for full details on health and safety and storage regulations.

Reviews

There are no reviews yet.

Be the first to review “Coo-var Suregrip”

You may also like…